Dataset: DNA metrics from minimally-lethal genotyping with eastern oysters (Crassostrea virginica) conducted in 2022 and 2023

Juvenile oysters ranging from 30mm to 60mm were sourced from the Aquaculture Genetics and Breeding Technology Center (ABC) at the Virginia Institute of Marine Science (VIMS). Each oyster was cleaned using a 1% bleach solution, air-dried for an hour, and labeled with a shellfish tag (Hallprint FPN 8x4 mm) using coral epoxy (Instant Ocean HoldFast® Epoxy Stick). 

To store the oysters before the experiment, the oysters were stored at 5°C for up to 48 hours before experimentation.

Treatment groups: We planned nine treatments to determine which protocol would have the best DNA yield with the lowest mortality (Figure 1 of Leung et al. 2026 (in press)). Each treatment had at least 20 individual oysters. The treatments and short names are described in Table 1 of Leung et al. 2026 (in press).

To establish a baseline for DNA quantification and quality, we sampled mantle, adductor, and gill tissues from 30 individuals and placed them into 2 mL O-ring vials with 95% molecular-grade ethanol. We stored the samples temporarily in a -20℃ freezer before transferring them to a -80℃ freezer.

Accessing the oyster tissue within the shell: Two methods were used to enter the oyster shell: creating a notch in the shell or relaxing the oyster. Creating a notch allowed for the extraction of fluid that contains genetic material (e.g., hemolymph or EPF), while relaxing the oyster allowed for tissue swabbing or direct sampling of the tissue.

1. Notch Protocol: A variable-speed dremel was used to make a small, V-shaped notch in the oyster shell, just large enough for the needle (BD 23G PrecisionGlide Needle) to fit in at different angles. The size of the notch depended on how much new shell an oyster had recently produced, but was typically a few mm in size. The notch was created on the right valve of the oyster, approximately two-thirds to the top of the shell. The needle, attached to a syringe (BD 1mL Syringe), was used to extract fluid as described below for the Hemolymph Protocol and the EPF Protocol.
2. Relaxation Protocol: For the relaxation protocol, 2 L of 1µm filtered seawater was mixed with 100g of Epsom salt until all the salt dissolved following protocol by Proestou et al. (2025). A maximum of ten oysters were placed in each replicate 2L container for 16 hours before the cell sampling (see Treatment Groups for experimental design). Oysters were fully submerged in the Epsom salt solution and held at room temperature. During relaxation, containers were aerated using air stones and airlines to maintain oxygen levels.

Collection of genetic material

Cell collection for notched oysters: Cells were collected from notched oysters by sampling hemolymph or EPF fluids. For the preservation of fluids, we split the samples and placed half in liquid nitrogen and the other half in FTA cards (see below):

1. Hemolymph Protocol: We inserted the needle through the notch diagonally down into the adductor muscle, which we identified through increased resistance. We collected 125 to 250 µL of hemolymph.
2. EPF Protocol: We inserted the needle into the notch until it reached the mantle cavity of the shell and collected 80 to 500 µL of EPF from each oyster. If necessary, we removed and reinserted the needle at multiple angles for small oysters to obtain a minimum fluid amount of 80 µL.

Cell collection for relaxed oysters: Cells were collected from relaxed oysters by taking a mantle biopsy or swabbing the mantle tissue.

1. Mantle Biopsy Protocol: We used forceps and scissors to remove a small piece (~10-20mg) of the mantle wrapped around the adductor muscle. We sampled the distal edge of the mantle tissue, approximately 2-3mm away from the visible edge of the adductor muscle. After each sample was acquired, we sterilized the forceps and scissors using an ethanol lamp.
2. Swab Protocol: Using an OmniSwap (Qiagen; WB100035), we swabbed in a circular motion, starting at the top layer of the mantle and moving down to the mantle around the adductor, then to the mantle’s bottom layer, and then reversing this path. The motion was repeated five times for each sampled individual.

Preservation of genetic material: We used three preservation protocols for the genetic samples: ethanol, flash-freezing, and FTA cards:

1. Ethanol Protocol: The mantle sampled from the relaxed oysters was preserved with 95% molecular-grade ethanol. It was temporarily stored in a -20℃ freezer and then transferred to a -80℃ freezer.
2. Flash-Freeze Protocol: Liquid nitrogen was used to flash-freeze half of each EPF or hemolymph sample from the notched oysters. After the samples were flash-frozen, they were stored in a -80℃ freezer. Additionally, the swabs used on the relaxed oysters were flash-frozen and then stored in a -80℃ freezer.
3. FTA Cards Protocol: The remaining half of the EPF and hemolymph samples were stored on QIAcard FTA Classic Cards (Qiagen; WB120305). Following the manufacturer's instructions, we put up to 125 µL of fluid on each circle in the FTA card. FTA cards were stored in WhirlPak bags with color-indicating silica beads (desiccants that absorb moisture and change color to indicate saturation) following the manufacturer’s recommendations.

DNA extraction: A Qiagen DNeasy Blood & Tissue kit (Qiagen; 69504) was used for all DNA extractions, but with slight modifications for different cell types or preservation methods. The manufacturer’s instructions were used for the control and the mantle biopsy groups with 20- 30mg of tissue, as well as the swabs (swabs were horizontally cut in half before extraction so that they could be submerged fully in the buffer). We modified the protocol for the EPF and Hemolymph samples by using 200 µL of the flash-frozen sample as input (based on preliminary trials of 20, 100, and 200 µL that showed the latter amount yielded the most DNA) but otherwise followed the manufacturer’s instructions. For the Whatman FTA Cards, we used a 6.0mm biopsy punch (Cenmed™ PMD Sterile, Disposable Biopsy Punches) to cut a disk from the middle of the card. Per recommendation from Sigma Aldrich, 280 microliters of the ATL buffer was added to the disk for extraction, and the remainder of the manufacturer’s instructions were followed (Reliable DNA Extraction from WhatmanTM FTA Cards, n.d.).

DNA quantification and quality assessment: We used a Qubit 3.0 Fluorometer to quantify DNA yield from the extractions. We used the High Sensitivity Kit (ThermoFisher; Q32851) for samples with a yield between 0 and 20 ng/ul and the Broad Range Kit (ThermoFisher; Q32850) for all samples with a yield higher than 20 ng/ul.

To test the quality of the DNA, we ran 3 μL of each DNA extract on a 1% agarose gel (0.6g of agarose with 60 mL of 1x TAE buffer), stained with GelRed at 130V for 30 minutes. Gels were visualized, and images were captured on a BioRad Gel Doc XR+ Molecular Imager machine. We categorized each sample on the gel into one of four levels: a bright band greater than 3000 bp with a slight smear (level 1), a completely smeared sample (level 2), a barely visible gel (level 3), or no band (level 4).